This site uses cookiesX
100% Guarantee & Free Delivery
View Cart (0)
0800 048 1057
0800 048 1057
Menu ▼

TM-SG4 RS-485 Pull-high/Pull-low And Termination Resistor Module

tM-SG4 RS-485 Pull-high/Pull-low and Termination Resistor Module
£2500

(£30.00 incl VAT)
FREE delivery to UK on orders over £100

100% Money Back
30 Day Guarantee

International Shipping
Over 100 Countries

Model:tM-SG4

Description

The tM-SG4 is a module that is used to improve the communication of RS-485 network.

It provides switch selectable pull-high and pull-low resistors on RS-485 network. It also has 15-step switch selectable termination resistor so the optimum termination resistor can be connected to the RS-485 network easily.

If the RS-485 network is not over 100 meters, the termination resistors are not needed. Otherwise, it may be necessary to insert two termination resistors at both ends of the RS-485 network. It is not easy to calculate the value of a termination resistor on the RS-485 network. The best way to do this is to use an oscilloscope to check the RS-485 signal directly. If the impedance match of RS-485 network is OK, the oscilloscope will show a clearly defined square wave. If the square wave signal is distorted, termination resistors will be needed at both ends of the RS-485 network.
tM-SG4 introduction

Features

  • Switch-selectable Pull-high/Pull-low Resistors
  • 15-step Switch-selectable Termination Resistor
  • LED Indicator for Power/Termination
  • DIN-Rail mountable
  • Cost-effective
  • Wide Operating Temperature Range: -25 °C ~ +75 °C

Specifications

RS-485 Interface
Pull-high/Pull-low Resistance 1 kΩ, 10 kΩ, 100 kΩ, Switch-selectable
Termination Resistance 15 Steps, 65 ~ 560 Ω
LED Indicators
Power 1 Red LED as Power Indicator
Termination Resistor 1 Green LED as Termination Indicator
EMS Protection
ESD (IEC 61000-4-2) ±4 kV Contact for Each Terminal
Power Requirements
Reverse Polarity Protection Yes
Powered from Terminal Block Yes, 10 ~ 30 VDC
Consumption 0.5 W Max.
Mechanical
Dimensions (W x L x H) 52 mm x 87 mm x 27 mm
Installation DIN-Rail Mounting
Environment
Operating Temperature -25 ~ +75 °C
Storage Temperature -40 ~ +85 °C
Humidity 10 ~ 90% RH, Non-condensing
 
Termination Resistance Settings
120R 330R 470R 560R Termination Resistance (Ω)
ON ON ON ON 65
ON ON ON OFF 74
ON ON OFF ON 76
ON OFF ON ON 81
ON OFF OFF ON 99
ON OFF ON OFF 96
ON ON OFF OFF 88
ON OFF OFF OFF 120
OFF OFF ON ON 144
OFF ON ON OFF 193
OFF ON OFF ON 207
OFF ON OFF OFF 330
OFF OFF ON ON 256
OFF OFF ON OFF 470
OFF OFF OFF ON 560
 
Pull-high and Pull-low Settings
1k 10k 100k RS-485 Data Line Status
OFF OFF OFF No pull-high/pull-low on RS-485 data line
ON OFF OFF 1k [ pull-high and pull-low
OFF ON OFF 10k [ pull-high and pull-low
OFF OFF ON 100k [ pull-high and pull-low
 
Termination Resistance On/Off Switch
OFF Termination Resistor do NOT work.
ON Termination Resistor is worked, and TR LED is light.

 

Technical

tM-SG4 Termination pull-up & pull-down module

Description

The tM-SG4 is a module that is used to improve the communication of RS-485 network.

It provides switch selectable pull-high and pull-low resistors on RS-485 network. It also has 15-step switch selectable termination resistor so the optimum termination resistor can be connected to the RS-485 network easily.

If the RS-485 network is not over 100 meters, the termination resistors are not needed. Otherwise, it may be necessary to insert two termination resistors at both ends of the RS-485 network. It is not easy to calculate the value of a termination resistor on the RS-485 network. The best way to do this is to use an oscilloscope to check the RS-485 signal directly. If the impedance match of RS-485 network is OK, the oscilloscope will show a clearly defined square wave. If the square wave signal is distorted, termination resistors will be needed at both ends of the RS-485 network.
tM-SG4 introduction

Features

Specifications

RS-485 Interface
Pull-high/Pull-low Resistance 1 kΩ, 10 kΩ, 100 kΩ, Switch-selectable
Termination Resistance 15 Steps, 65 ~ 560 Ω
LED Indicators
Power 1 Red LED as Power Indicator
Termination Resistor 1 Green LED as Termination Indicator
EMS Protection
ESD (IEC 61000-4-2) ±4 kV Contact for Each Terminal
Power Requirements
Reverse Polarity Protection Yes
Powered from Terminal Block Yes, 10 ~ 30 VDC
Consumption 0.5 W Max.
Mechanical
Dimensions (W x L x H) 52 mm x 87 mm x 27 mm
Installation DIN-Rail Mounting
Environment
Operating Temperature -25 ~ +75 °C
Storage Temperature -40 ~ +85 °C
Humidity 10 ~ 90% RH, Non-condensing
 
Termination Resistance Settings
120R 330R 470R 560R Termination Resistance (Ω)
ON ON ON ON 65
ON ON ON OFF 74
ON ON OFF ON 76
ON OFF ON ON 81
ON OFF OFF ON 99
ON OFF ON OFF 96
ON ON OFF OFF 88
ON OFF OFF OFF 120
OFF OFF ON ON 144
OFF ON ON OFF 193
OFF ON OFF ON 207
OFF ON OFF OFF 330
OFF OFF ON ON 256
OFF OFF ON OFF 470
OFF OFF OFF ON 560
 
Pull-high and Pull-low Settings
1k 10k 100k RS-485 Data Line Status
OFF OFF OFF No pull-high/pull-low on RS-485 data line
ON OFF OFF 1k [ pull-high and pull-low
OFF ON OFF 10k [ pull-high and pull-low
OFF OFF ON 100k [ pull-high and pull-low
 
Termination Resistance On/Off Switch
OFF Termination Resistor do NOT work.
ON Termination Resistor is worked, and TR LED is light.

 

Technical

tM-SG4 Termination pull-up & pull-down module

Recently Viewed Products