NSM-206FCS Rugged 4-port Industrial Ethernet Switch with Dual FX Fibre

NSM-206FCS 4 port Ethernet + Dual Fibre Switch (SC)-Rugged- 15km

£342.00

The NSM-206FCS (SC Connector; Single-mode) is a Unmanaged 4-Port Industrial 10/100 Base-T(X) with Dual 100 Base-FX Switch that secures data transmission by using fibre optic transmission to provide immunity from EMI/RFI interference. It can be used for transmitting an Ethernet signal up to 15 Km, and is the perfect solution for applications where transmission must be protected from electrical exposure, surges, lightning or chemical corrosion.

The NSM-206FCS operates at full duplex mode. In full duplex mode, range is 15km with 8.3/125, 8.7/125, 9/125 or 10/125 μm fibre cables.

The NSM-206FCS can extend your LAN in a daisy chain configuration. Please refer to the User manual.

NSM-206FCS provides two power inputs that can be connected simultaneously to live DC power sources. If one of the power inputs fails, the other live source acts as a backup to automatically support the NSM-206FCS's power needs.

This unit is supplied in an IP20 rugged, high-strength steel case capable of either DIN-Rail or Wall Mounting.

NSM-206FCS 4 port Ethernet + Dual Fibre Switch (SC)-Rugged- 15km

Quantity:

Features

Automatic MDI / MDI-X crossover for plug-and-play

Each port supports both 10/100 Mbps speed auto negotiation

Store-and-forward architecture

Full duplex IEEE 802.3x and half duplex backpressure flow control

1.6 Gbps high performance memory bandwidth.

Redundant +10 ~ +30Vdc voltage
Power failure alarm by relay output

Supports operating temperatures from 0 ~ +70°C

IP20 rugged hugh-strength metal case

DIN rail mount for industrial usage and screw hole for wall mounting

Specifications

Technology

Standards : IEEE802.3, 802.3u, 802.3x

Processing Type : Store & forward wire speed switching - no delays

MAC Addresses : 1024

Memory Bandwidth : 1.6 Gbps

Flow Control : IEEE802.3x flow control, back pressure flow control

Interface

RJ45 Ports : 10/100 Base-T(X) auto negotiation speed, F/H duplex mode,
and auto MDI/MDIX connection

Fibre Optic Port : 100 Base-FX (Single-mode, SC Connector)

LED Indicators : 10/100M, Link/Act, Full/Half Duplex (Fibre port)

Ethernet isolation : 1500 Vrms 1 minute

Frame Ground for EMS Protection : Yes

Fibre Optic : Single-mode fibre cables : 8.3/125, 8.7/125, 9/125 or 10/125µm
Distance : 15km (9/125µm recommended) for full duplex
Wavelength : 1300 or 1310 nm
Min. Tx Output : -15 dBm
Max. Tx Output : -8 dBm
Rx Sensitivity : -36 to -31 dBm

Cable : Ethernet : 2-pair UTP/STP Cat.3,4,5, EIA/TIA-568 100-ohm
Fast Ethernet : 2-pair UTP/STP Cat. 5, EIA/TIA-568 100-ohm

Power

Redundant Input Range : +10 ~ +30VDC (Non-isolation)

Alarm Contact : one relay output with current carrying capacity of 2A @ 30Vdc

Power Consumption : 0.24A@24VDC, +/- 5% arrowed with 100M Full duplex.

LED Indicator : Power Input 1, Power Input 2, Power Fail

Protection : Power reverse polarity protection

Frame Ground for EMS Protection : Yes

Connection : 7-Pin Removable Terminal Block

Mechanical

Case : Metal

Environmental Rating : IP20

Dimensions : 72.5mm x 110mm x 102mm (W x H x D)

Installation : DIN Rail Mount, Wall Mounting

Environmental

Operating Temperature : 0 to 70 °C

Storage Temperature : -20 to 85 °C

Ambient Relative Humidity : 10% to 90% non-condensing

Technical

User Manual

Recommendations

Power Supplies