I-7540D Ethernet to CAN Bus Gateway Measurement Systems

I-7540D Ethernet to CAN Bus Gateway

£198.00

Internet communications using TCP/IP is increasing in the industrial sector. Using Ethernet for networking in industrial areas is appealing because the required cabling is already installed. The CAN-Ethernet Gateway from ICP DAS is a solution that enables CAN networks to be coupled together over the Internet/Ethernet, whereby remote monitoring and control is possible. The CAN-Ethernet Gateway controls networked communication and makes a transparent CAN-based application interface available to the user.

The i-7540D device supports a transparent, protocol-independent transfer of the CAN messages, thus allowing its implementation into a wide range of possible applications. Furthermore, the CAN-Ethernet Gateway can be used with various higher layer CAN protocols (e.g. CANopen, DeviceNet or other proprietary protocols).

Furthermore, the i-7540D can also be used as an Ethernet to CAN/RS-232/485 Device Server. The Device Server is an appliance that network enables any device with a serial communication port. By virtue of its independent operating system, protocol independence, small size and flexibility, Device servers are able to meet the demand of virtually any network-enabled application. Many devices don't have network ports. The i-7540D allows those devices to become connected to the network.

Quantity:

Features

80186-80 Embedded CPU, or compatible

Ethernet Protocols, TCP,UDP,IP,ICMP,ARP

10/100 Base-TX Ethernet Controller

Reloadable Operating Software

Message transmitted by using TCP/IP protocol

Diagnostics

COM driver support interrupt & 1K QUEUE Input & Output buffer

Support one RS-232 port, one RS-485 port and one CAN port

2500Vrms photo-isolation protection on CAN side.

Jumper select 120Ω terminator resistor for CAN channel

Philips 82C 250/251CAN Transceiver

Support both CAN specification 2.0A and 2.0B.

Max transmission speed up to 1M bps for CAN and 115.2K bps for RS-232 & RS-485

Max transmission distance of CAN over 1000m (follow CAN specification)

Built-in self-tuner ASIC controller on RS-485 port

7-segment LED display.

Software configurable CAN and RS-232 communication parameters

Firmware updated from COM1 or Ethernet port

Support Web Configuration

Support max 25 Ethernet clients connection

Support for Virtual COM technology

Specifications

CPU

Type : 80186, 80MHz or compatible
SRAM : 512K Bytes
Flash : 512K Bytes
EEPROM : 16K Bytes
NVRAM : 31 Bytes (battery backup, data valid up to 10 year)
RTC (Real Time Clock) : Yes
64-bit Hardware Serial Number : Yes
Built-in Watchdog Timer : Yes

Communication Interface

COM1 : RS-232 (TXD, RXD, RTS, CTS, GND)
COM2 : RS-485 (D2+, D2-)
CAN : One CAN port with two CAN bus connector interfaces (CAN_H, CAN_L)
Ethernet Port : 10/100Base-TX Ethernet Controller
(Auto-negotiating, Auto_MDIX, LED indicator)

COM Port Formats

Data Bit : 7,8
Parity : Even, Odd, None
Stop Bit : 1
Baud-rate : 115.2 Kbps max.

CAN Port

CAN Controller : Philips SJA1000T CAN Controller
CAN Transceiver : Philips 82C250 CAN Transceiver
Isolated : 2500Vrms on CAN side
Baud-rate : 1Mbps max.

Dimensions

123 x 72 x 33 mm (W x D x H)

Environment

Operating Temperature : -25 to 75 °C
Storage Temperature : -40 to 80 °C

Power

Protection : Power reverse polarity protection
Frame Ground for ESD Protection : Yes
Required Supply Voltage : +10 to +30VDC (non-regulated)
Power consumption : 2.5W

Technical

Quickstart Guide
User Manual
Firmware Download Instructions

Applications

Factory Automation

Building Automation

Home Automation

Control System

Monitor System

Vehicle Automation

Recommendations

Power Supplies